An OSPF Stub Area helps in simplifying routing in larger OSPF networks and makes routing more efficient. Routers in a stub area do not flood external (Type 5) LSAs and Type 3 LSAs (depending on the type of stub area).

Routers within a stub area only know internal routes, making routing tables smaller and more efficient. SPF calculation is simpler and faster convergence is possible.

Configuration Steps

Step 1: Configure IP addresses on interfaces on all routers.

*****************************R1
enable
configure terminal
!
interface Loopback0
 ip address 1.1.1.1 255.255.255.255
!
interface FastEthernet0/0
 ip address 10.10.10.0 255.255.255.254
 no shutdown
!
interface FastEthernet0/1
 ip address 10.10.10.2 255.255.255.254
 no shutdown
!
interface FastEthernet1/0
 ip address 30.30.30.0 255.255.255.254
 no shutdown
!

*****************************R2
enable
configure terminal
!
interface Loopback0
 ip address 2.2.2.2 255.255.255.255
!
interface FastEthernet0/0
 ip address 20.20.20.2 255.255.255.254
 no shutdown
!
interface FastEthernet0/1
 ip address 20.20.20.0 255.255.255.254
 no shutdown
!
interface FastEthernet1/0
 ip address 30.30.30.1 255.255.255.254
 no shutdown
!

*****************************R3
enable
configure terminal
!
interface Loopback0
 ip address 3.3.3.3 255.255.255.255
!
interface FastEthernet0/0
 ip address 10.10.10.1 255.255.255.254
 no shutdown
!
interface FastEthernet0/1
 ip address 10.10.10.4 255.255.255.254
 no shutdown
!

*****************************R4
enable
configure terminal
!
interface Loopback0
 ip address 4.4.4.4 255.255.255.255
!
interface FastEthernet0/0
 ip address 10.10.10.3 255.255.255.254
 no shutdown
!
interface FastEthernet0/1
 ip address 10.10.10.5 255.255.255.254
 no shutdown
!

*****************************R5
enable
configure terminal
!
interface Loopback0
 ip address 5.5.5.5 255.255.255.255
!
interface FastEthernet0/0
 ip address 20.20.20.3 255.255.255.254
 no shutdown
!
interface FastEthernet0/1
 ip address 20.20.20.4 255.255.255.254
 no shutdown
!

*****************************R6
enable
configure terminal
!
interface Loopback0
 ip address 6.6.6.6 255.255.255.255
!
interface FastEthernet0/0
 ip address 20.20.20.1 255.255.255.254
 no shutdown
!
interface FastEthernet0/1
 ip address 20.20.20.5 255.255.255.254
 no shutdown
!

Step 2: Configure OSPF on all the routers.

******************************R1
router ospf 10
 router-id 1.1.1.1
 log-adjacency-changes
 network 1.1.1.1 0.0.0.0 area 0
 network 10.10.10.0 0.0.0.1 area 2
 network 10.10.10.2 0.0.0.1 area 2
 network 30.30.30.0 0.0.0.1 area 0
!

******************************R2
router ospf 10
 router-id 2.2.2.2
 log-adjacency-changes
 network 2.2.2.2 0.0.0.0 area 0
 network 20.20.20.0 0.0.0.1 area 2
 network 20.20.20.2 0.0.0.1 area 2
 network 30.30.30.0 0.0.0.1 area 0
!

******************************R3
router ospf 10
 router-id 3.3.3.3
 log-adjacency-changes
 network 3.3.3.3 0.0.0.0 area 0
 network 10.10.10.0 0.0.0.1 area 2
 network 10.10.10.4 0.0.0.1 area 2
!

******************************R4
router ospf 10
 router-id 4.4.4.4
 log-adjacency-changes
 network 4.4.4.4 0.0.0.0 area 0
 network 10.10.10.2 0.0.0.1 area 2
 network 10.10.10.4 0.0.0.1 area 2
!

******************************R5
router ospf 10
 router-id 5.5.5.5
 log-adjacency-changes
 network 5.5.5.5 0.0.0.0 area 0
 network 20.20.20.2 0.0.0.1 area 1
 network 20.20.20.4 0.0.0.1 area 1
!

******************************R6
router ospf 10
 router-id 6.6.6.6
 log-adjacency-changes
 network 6.6.6.6 0.0.0.0 area 0
 network 20.20.20.0 0.0.0.1 area 1
 network 20.20.20.4 0.0.0.1 area 1
!

Step 3: Verify OSPF adjacent status on all routers

Step 4: Create Loopback 100 on R3 and redistribute it into OSPF as an external route.

******************************R3
!
interface Loopback100
 ip address 100.100.100.100 255.255.255.255
!
ip prefix-list DISTRIBUTE_DIRECT seq 10 permit 100.100.100.100/32
!
route-map DISTRIBUTE_DIRECT permit 10
 match ip address prefix-list DISTRIBUTE_DIRECT
!
router ospf 10
redistribute connected subnets route-map DISTRIBUTE_DIRECT
!

Step 5: Verify LSDB on all routers. As shown below, R3 and R5 have received Type 5 LSAs in their LSDB.

Step 6: Configure Area 1 as Stub area. Run stub command on R2, R5 and R6.

Note: The stub command must be run on all routers in Area 1 for the area to be stub area. The adajaceny relationship will go down if stub is configured only on one of the adjacent routers.

***************************R2,R5,R6
!
router ospf 10
area 1 stub
!

Step 7: Verify the routing table of R5 and R6

Thank you for reading this article, please leave your comments in the comments section and check other related posts on our website.

Related Posts

• L2 EVPN Implementation on Huawei Routers.
• VRRP Monitoring of the Uplink Interface status on Huawei routers.
• Association between VRRP and BFD Implementation on Huawei routers.
• Association between VRRP and STP Implementation on Huawei routers.
• VRRP Implementation on Huawei Routers.